ماكينة كيوسيرا للتصوير Kyocera 3035

 ماكينة تصوير كيوسيرا 3050

ماكينة كيوسيرا للتصوير - Kyocera KM3035

تعريف ماكينة تصوير كيوسيرا 3050:

ماهي ماكينة تصوير كيوسيرا 3035؟

تم انتاج ماكينة تصوير كيوسيرا 3035 الالمانية في أواخر عام 2003 ، وتم اصدارها بسعر السوق المحلي 6000 دولار وهي أحدث الموديل ،حيث تنتج هذه الآلة مالا يقل عن 85000 نسخة بشكل شهري وهي مثالية للأعمال التجارية الصغيرة أو الطابعات البسيطة.

آلة التصوير هذه هي أحادية اللون تعمل بسرعة 30صفحة في الدقيقة ، وهي مناسبة لجهاز الكمبيوتر أو الكمبيوتر الشخصي وجميع ماكينات التصوير لدينا تم تجربتها وفي حالة جيدة ، فنحن كفريق عمل واحد نسعى لنقدم لك آلات التصوير التي تحتاجها بالسعر المناسب لك .

مواصفات فنية استخدام لماكينة تصوير كيوسيرا 3035:

تم انتاج وتصنيع ماكينة تصوير كيوسيرا 3035 من مكونات طويلة العمر مع امكانيه سهولة الصيانة وتوفر قطع الغيار والوان الطباعة بجوده عالية .

• المواصفات العامة : طباعة على الوجهين.

• عدد النسخ: 40 نسخة في الدقيقة.

• أوزان الورق: من 9 جرام -42 جرام.

• وزن الماكينة : 180 كيلو جرام.

• زمن مدة التسخين :3,9 ثانية.

• دقة الطباعة : 600 x 600 dpi.

• دقة التصوير :600 x 600 dpi.

• سعة الدرج الخاص: 200 ورقة.

• الحجم الطبيعي 11 x 17.

• سرعة الماكينة : 50 صورة بالدقيقة.

• سعة الذاكرة الداخلية :تخزين 64ميجابايت.

مميزات آلات تصوير مستندات كيوسيرا كم 3035:

آلات تصوير مستندات كيوسيرا كم 3035 مناسبة للطباعة بأحجام صفحات مختلفة تتراوح بين A3 إلى A5 كما أن أنواع الورق المستخدم بها هو ورق عادي ، لامع ، ورق مقوى بأوزان تصل إلى 300 جم / م 2 .

تتميز آلات تصوير مستندات كيوسيرا كم 3035 بأقصى سرعة ودقة عاليه ونطاق التكبير المذهل المثالي عند تشغيل خاصية مسح ضوئي والطباعة بجودة عالية وفي وقت قصير للغاية كما انها تشغل مساحة أقل.. بالإضافة الي كل هذه المميزات فإن آلات تصوير مستندات كيوسيرا كم 3035 من السهل صيانتها حيث تتوافر جميع قطع الغيار الخاصة بها أو أحبار للطباعه  في الأسواق.

سعر ماكينة تصوير كيوسيرا 3035:

• سعر ماكينة تصوير كيوسيرا 3035 استعمال الخارج ( ).

• سعر ماكينة تصوير كيوسيرا 3035 جديدة ( ).

كتالوج ماكينة تصوير كيوسيرا 3035:

يمكنك الان تصفح الكتالوج الخاصل لكيوسيرا 3035 لتحميل كتالوج آلة كيوسيرا 3035  اضغط هنا

اكواد اعطال ماكينة تصوير كيوسيرا 3035 - Kyocera 3035

عطل كيوسيرا كود ( Code: 0030 )

وصف الكود:

Fax control PCB problem • Problems with data from fax control PCB.

السبب:

Defective fax control PCB.

حل مشكلة الكود

Replace the fax control PCB and check for correct operation.

 

)Code:  0070 عطل كيوسيرا كود (

وصف الكود:

Abnormal detection of fax control PCB incompatibility • In the initial communication with the fax control PCB, any normal communication command is not transmitted.

السبب:

Defective fax software. Defective fax control PCB.

حل مشكلة الكود

Install the fax software to Ver. 2.xx or later. Replace the fax control PCB and check for correct operation.

 

)Code:  0100 عطل كيوسيرا كود (

وصف الكود:

Operation unit PCB backup memory read/write error • Reading from or writing to the backup memory cannot be performed.

السبب:

Defective EEPROM.

حل مشكلة الكود :

Replace EEPROM 3 and 4.

)Code:  0110 عطل كيوسيرا كود (

وصف الكود:

Operation unit PCB backup memory data problem • Data in the specified area of the backup memory does not match the specified values. (This code is not displayed. The service call counter counts the frequency of occurrence only as for this code.)

السبب:

Problem with the backup memory data. Defective backup RAM.

حل مشكلة الكود

Turn safety switch 1 off and back on and run maintenance item U020 to set the contents of the backup memory data again. If the C0110 is displayed after re-setting the backup memory contents, replace the backup RAM.

)Code:  0150 عطل كيوسيرا كود (

وصف الكود:

Backup memory read/write error 2 • Reading from or writing to the backup memory cannot be performed.

السبب:

Defective EEPROM.

حل مشكلة الكود

Replace EEPROM 1 and 2.

)Code: C0160 عطل كيوسيرا كود (

وصف الكود:

Backup memory data problem • A checksum error in backup data is detected. (This code is not displayed. The service call counter counts the frequency of occurrence only as for this code.

السبب:

Data damage of EEPROM.

حل مشكلة الكود

Contact the Service Administrative Division.

)Code: C0170( عطل كيوسيرا كود

وصف الكود:

Accounting count error • A checksum error in backup data of the accounting counter is detected.

السبب:

Data damage of EEPROM.

حل مشكلة الكود

Contact the Service Administrative Division.

)Code: C0210 عطل كيوسيرا كود(

وصف الكود:

MMI communication problem • There is no reply after 20 retries at communication.

السبب:

Defective main PCB.

حل مشكلة الكود

Replace the main PCB and check for correct operation.

 

)Code: C0240 عطل كيوسيرا كود(

وصف الكود:

Printer board communication problem • There is no reply after 20 retries at communication.

السبب:

Poor contact in the connector terminals. Defective main PCB or printer board.

حل مشكلة الكود

Check the connection of connector YC43 on the main PCB and the connector on the printer board. Repair or replace if necessary. Replace the main PCB or printer board and check for correct operation.

)Code: C0250 عطل كيوسيرا كود(

وصف الكود:

Scanner network board communication problem • There is no reply after 20 retries at communication.

السبب:

Poor contact in the connector terminals. Defective main PCB or scanner network board.

حل مشكلة الكود:

Check the connection of connector YC46 on the main PCB and the connector on the memory PCB. Repair or replace if necessary. Replace the main PCB or scanner network board and check for correct operation.

)Code: C0280 عطل كيوسيرا كود(

وصف الكود:

Fax control PCB communication problem • There is no reply after 20 retries at communication.

السبب:

Poor contact in the connector terminals. Defective main PCB or fax control PCB.

حل مشكلة الكود:

Check the connection of connector YC44 on the main PCB and the connector on the memory PCB. Repair or replace if necessary. Replace the main PCB or fax control PCB and check for correct operation.

 

)Code: C0320 عطل كيوسيرا كود(

وصف الكود:

Energy saves communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.

السبب:

Defective main PCB.

حل مشكلة الكود:

Replace the main PCB and check for correct operation.

)Code: C0420 عطل كيوسيرا كود(

وصف الكود:

Large paper deck/paper feeder communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.

السبب:

Poor contact in the connector terminals. Defective main PCB. Defective deck main PCB/desk main PCB.

حل مشكلة الكود:

Check the connection of connectors CN3 on the main PCB and the connector on the deck main PCB/desk main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the deck main PCB/desk main PCB and check for correct operation.

Code: C0440 عطل كيوسيرا كود (

وصف الكود:

Finisher communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.

السبب:

Poor contact in the connector terminals. Defective main PCB. Defective finisher main PCB.

حل مشكلة الكود:

Check the connection of connectors YC4, YC5 on the main PCB and CN2 on the finisher main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the finisher main PCB and check for correct operation.

)Code: C0450 عطل كيوسيرا كود(

وصف الكود:

Mailbox communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.

السبب:

Poor contact in the connector terminals. Defective main PCB. Defective mailbox main PCB.

حل مشكلة الكود:

Check the connection of connectors YC3 on the main PCB and CN1 on the mailbox main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the mailbox main PCB and check for correct operation.

)Code: C0470 عطل كيوسيرا كود(

وصف الكود:

Switchback unit communication problem • Communication errors from the communication microcomputer on the main PCB. No communication: there is no reply after 5 retries. Abnormal communication: a communication error (parity or checksum error) is detected five times in succession.

السبب:

Poor contact in the connector terminals. Defective main PCB. Defective switchback unit main PCB.

حل مشكلة الكود:

Check the connection of connectors YC3 on the main PCB and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the switchback unit main PCB and check for correct operation.

 

)Code: C0610 عطل كيوسيرا كود(

وصف الكود:

Bitmap problem • There is a problem with the data or address bus of the bitmap DRAM. • The DIMM on the memory PCB does not operate correctly.

السبب:

Defective main PCB. DIMM installed incorrectly. Defective DIMM.

حل مشكلة الكود:

Replace the main PCB and check for correct operation. Check if the DIMM is inserted into the socket on the main PCB correctly. Replace the DIMM and check for correct operation.

)Code: C0630 عطل كيوسيرا كود(

وصف الكود:

DMA problem • DMA transmission of compressed, decompressed, rotated, relocated or blanked-out image data does not complete within the specified period of time.

السبب:

Defective main PCB.

حل مشكلة الكود:

Replace the main PCB and check for correct operation.

)Code: C0640 عطل كيوسيرا كود(

وصف الكود:

Hard disk drive problem • The hard disk drive cannot be accessed.

السبب:

Poor contact of the hard disk drive connector terminals. Defective hard disk drive. Defective main PCB.

حل مشكلة الكود:

Check the connection of connectors YC49 on the main PCB and hard disk drive, and the continuity across the connector terminals. Repair or replace if necessary. Run U024 (HDD formatting) without turning the power off to initialize the hard disk. Replace the hard disk drive and check for correct operation if the problem is still detected after initialization. Replace the main PCB and check for correct operation.

 

)Code: C0820 عطل كيوسيرا كود(

وصف الكود:

Fax control PCB CG ROM checksum error • A checksum error occurred with the CG ROM data of the fax control PCB.

السبب:

Defective fax software. Defective fax control PCB.

حل مشكلة الكود:

Install the fax software to Ver. 2.xx or later. Replace the fax control PCB and check for correct operation.

 

)Code: C0830 عطل كيوسيرا كود(

وصف الكود:

Fax control PCB flash program area checksum error • A checksum error occurred with the program of the fax control PCB.

السبب:

Defective fax software. Defective fax control PCB.

حل مشكلة الكود:

Install the fax software to Ver. 2.xx or later. Replace the fax control PCB and check for correct operation.

)Code: C0860 عطل كيوسيرا كود(

وصف الكود:

Fax control PCB software switch checksum error • A checksum error occurred with the software switch value of the fax control PCB.

السبب:

Defective fax software. Defective fax control PCB.

حل مشكلة الكود:

Install the fax software to Ver. 2.xx or later. Replace the fax control PCB and check for correct operation.

 

)Code: C0870 عطل كيوسيرا كود(

وصف الكود:

Graphics data transfer problem • High-capacity data transfer between the fax control PCB and the main PCB was not normally performed even if the data transfer was retried the specified times.

السبب:

Poor contact in the connector terminals. Defective main PCB or fax control PCB.

حل مشكلة الكود:

Check the connection of connector YC44 on the fax control PCB and the main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB or fax control PCB and check for correct operation.

)Code: C0880 عطل كيوسيرا كود(

وصف الكود:

Program archive problem • When power is turned on, the compressed program in the Flash ROM on the fax control PCB was not successfully decompressed.

السبب:

Defective fax software. Defective fax control PCB.

حل مشكلة الكود:

Install the fax software to Ver. 2.xx or later. Replace the fax control PCB and check for correct operation.

)Code: C0890 عطل كيوسيرا كود(

وصف الكود:

Fax control PCB CG FONT archive problem • When power is turned on, the compressed CG font in the Flash ROM on the fax control PCB was not successfully decompressed.

السبب:

Defective fax software. Defective fax control PCB.

حل مشكلة الكود:

Install the fax software to Ver. 2.xx or later. Replace the fax control PCB and check for correct operation.

)Code: C0900 عطل كيوسيرا كود(

وصف الكود:

Fax control PCB incompatibility detection problem • Fax software is not compatible with MMI software.

السبب:

Fax software version is earlier.

حل مشكلة الكود:

Check the version of fax software and upgrade it to a version that accommodates the machine.

(Code: C1010 عطل كيوسيرا كود(

وصف الكود:

Upper lift motor problem • When the upper drawer is inserted, the upper lift limit switch does not turn on within 6 s of the upper lift motor turning on and the upper lift limit switch does not turn on in a retry operation after turning off the upper lift motor for 200 ms. At this time, removal and insertion of the drawer is prompted. Even after removal and insertion of the drawer, the upper lift limit switch does not turn on. This problem occurs four times continuously. • During copying, the upper lift limit switch does not turn on within 200 ms of the upper lift motor turning on. At this time, removal and insertion of the drawer is prompted. Even after removal and insertion of the drawer, the upper lift limit switch does not turn on. This problem occurs four times continuously.

السبب:

Broken gears or couplings of the upper lift motor. Defective upper lift motor. Poor contact of the upper lift motor connector terminals. Defective upper lift limit switch. Poor contact of the upper lift limit switch connector terminals.

حل مشكلة الكود:

Replace the upper lift motor. Check for continuity across the coil. If none, replace the upper lift motor. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check if YC13-B9 on the main PCB goes low when the upper lift limit switch is turned off. If not, replace the upper lift limit switch. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.

)Code: C1020 عطل كيوسيرا كود(

وصف الكود:

Lower lift motor problem • When the lower drawer is inserted, the lower lift limit switch does not turn on within 6 s of the lower lift motor turning on and the lower lift limit

switch does not turn on in a retry operation after turning off the lower lift motor for 200 ms. At this time, removal and insertion of the drawer is prompted. Even after removal and

insertion of the drawer, the lower lift limit switch does not turn on. This problem occurs four times continuously. • During copying, the lower lift limit switch does not turn on within 200 ms of the lower lift motor turning on. At this time, removal and insertion of the drawer is prompted. Even after removal and insertion of the drawer, the lower lift limit switch does not turn on. This problem occurs four times continuously.

السبب:

Broken gears or couplings of the lower lift motor. Defective lower lift motor. Poor contact of the lower lift motor connector terminals. Defective lower lift limit switch. Poor contact of the lower lift limit switch connector terminals.

حل مشكلة الكود

Replace the lower lift motor. Check for continuity across the coil. If none, replace the lower lift motor. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check if YC13-B15 on the main PCB goes low when the lower lift limit switch is turned off. If not, replace the lower lift limit switch. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.

)Code: C1030 عطل كيوسيرا كود(

وصف الكود:

Desk upper lift motor problem • When the upper drawer of the optional paper feeder is inserted, the desk upper lift limit switch does not turn on within 10 s of the desk upper lift motor turning on. At this time, removal and insertion of the drawer is prompted. Even after removal and insertion of the drawer, the upper lift limit switch does not turn on. This problem occurs four times continuously.

السبب:

Broken gears or couplings of the desk upper lift motor. Defective desk upper lift motor. Poor contact of the desk upper lift motor connector terminals. Defective desk upper lift limit switch. Poor contact of the desk upper lift limit switch connector terminals.

حل مشكلة الكود:

Replace the desk upper lift motor. Check for continuity across the coil. If none, replace the desk upper lift motor. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check if CN1-5 on the desk main PCB goes low when the desk upper lift limit switch is turned off. If not, replace the desk upper lift limit switch. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.

)Code: C1040 عطل كيوسيرا كود(

وصف الكود:

Desk lower lift motor problem • When the lower drawer of the optional paper feeder is inserted, the desk lower lift limit switch does not turn on within 10 s of the desk lower lift motor turning on. At this time, removal and insertion of the drawer is prompted. Even after removal and insertion of the drawer, the lower lift limit switch does not turn on. This problem occurs four times continuously.

السبب:

Broken gears of couplings of the desk lower lift motor. Defective desk lower lift motor. Poor contact of the desk lower lift motor connector terminals. Defective desk lower lift limit switch. Poor contact of the desk lower lift limit switch connector terminals.

حل مشكلة الكود:

Replace the desk lower lift motor. Check for continuity across the coil. If none, replace the desk lower lift motor. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check if CN1-7 on the desk main PCB goes low when the desk lower lift limit switch is turned off. If not, replace the desk lower lift limit switch. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.

)Code: C1100 عطل كيوسيرا كود(

وصف الكود:

Paper deck motor 1 problem • A motor over-current signal is detected continuously for 1 s or longer.

السبب:

Paper deck motor 1 does not rotate correctly (the motor is overloaded). Paper deck motor 1 connector makes poor contact.

حل مشكلة الكود

Check the gears and remedy if necessary. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable

)Code: C1110 عطل كيوسيرا كود(

وصف الكود:

Paper deck motor 2 problem • A motor over-current signal is detected continuously for 1 s or longer.

السبب:

Paper deck motor 2 does not rotate correctly (the motor is overloaded). Paper deck motor 2 connector makes poor contact.

حل مشكلة الكود

Check the gears and remedy if necessary. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable.

)Code: C1120 عطل كيوسيرا كود(

وصف الكود:

Deck right lift position problem • Deck level switch 2 does not turn on within 30 s of paper deck motor 2 turning on.

السبب:

Defective deck level switch 2. Poor contact of deck level switch 2 connector terminals. Defective paper deck motor 2. Poor contact of paper deck motor 2 connector terminals. The deck right lift does not rise properly.

حل مشكلة الكود

Check if CN5-4 on the desk main PCB goes low when desk level switch 2 is turned off. If not, replace desk level switch 2. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check for continuity across the coil. If none, replace paper desk motor 2. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check the gears and belts, and remedy if necessary.

)Code: C1130 عطل كيوسيرا كود(

وصف الكود:

Deck left lift position problem • Deck level switch 1 does not turn on within 30 s of paper deck motor 1 turning on.

السبب:

Defective deck level switch 1. Poor contact of deck level switch 1 connector terminals. Defective paper deck motor 1. Poor contact of paper deck motor 1 connector terminals. The deck left lift does not rise properly.

حل مشكلة الكود

Check if CN5-7 on the desk main PCB goes low when desk level switch 1 is turned off. If not, replace desk level switch 1. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check for continuity across the coil. If none, replace paper desk motor 1. Reinsert the connector. Also check for continuity within the connector cable. If none, repair or replace the cable. Check the gears and belts, and remedy if necessary.

)Code: C2000 عطل كيوسيرا كود(

وصف الكود:

Drive motor problem • LOCK ALM signal remains high for 1 s, 1 s after the drive motor has turned on.

السبب:

Poor contact in the drive motor connector terminals. Defective drive motor rotation control circuit. Defective drive transmission system.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the drive motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.

)Code: C2500 عطل كيوسيرا كود(

وصف الكود:

Paper feed motor problem • LOCK ALM signal remains high for 1 s, 1 s after the paper feed motor has turned on.

السبب:

Poor contact in the paper feed motor connector terminals. Defective paper feed motor rotation control circuit. Defective drive transmission system.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the paper feed motor. Check if the rollers and gears rotate smoothly. If not, grease the bushings and gears. Check for broken gears and replace if any.

)Code: C2600 عطل كيوسيرا كود(

وصف الكود:

Deck conveying motor/desk drive motor problem • No pulse is input within 500 ms of the start-up. • No pulse is input within 100 ms of the previous pulse input.

السبب:

Defective deck conveying motor PCB/desk drive motor PCB. Deck conveying motor /desk drive motor does not rotate correctly (the motor is overloaded). Poor contact in the deck conveying motor/desk drive motor connector terminals.

حل مشكلة الكود

Replace the deck conveying motor PCB/ desk drive motor PCB and check for correct operation. Check the gears and remedy if necessary. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable.

)Code: C3100 عطل كيوسيرا كود(

وصف الكود:

Scanner carriage problem • The home position is not correct when the power is turned on or at the start of copying using the bypass table.

السبب:

Poor contact in the connector terminals. Defective scanner home position switch. Defective main PCB or scanner drive PCB. Defective scanner motor.

حل مشكلة الكود

Check the connection of connector YC37 on the main PCB and the continuity across the connector terminals. Repair or replace if necessary. Replace the scanner home position switch. Replace the main PCB or scanner drive PCB and check for correct operation. Replace the scanner motor.

)Code: C3200 عطل كيوسيرا كود(

وصف الكود:

Exposure lamp problem • non-lighting of the exposure lamp is detected at the beginning of copying.

السبب:

Poor contact of the connector terminals. Defective main PCB. Defective exposure lamp.

حل مشكلة الكود

Check the connection of connector YC34 on the main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the exposure lamp or inverter PCB and check for correct operation.

)Code: C3300 عطل كيوسيرا كود(

وصف الكود:

Optical system problem • After AGC, correct input is not obtained at CCD. (This code is not displayed. The service call counter counts the frequency of occurrence only as for this code.)

السبب:

Poor contact of the connector terminals. Defective main PCB. Defective exposure lamp.

حل مشكلة الكود

Check the connection of connector YC34 on the main PCB, and the continuity across the connector terminals. Repair or replace if necessary. Replace the main PCB and check for correct operation. Replace the exposure lamp or inverter PCB and check for correct operation.

)Code: C4000 عطل كيوسيرا كود(

وصف الكود:

Polygon motor synchronization problem • When the polygon motor starts, the motor does not become stable even after 20 s.

السبب:

Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective power source PCB. Defective main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Check if 24 V DC is supplied to YC2-1 on the main PCB. If not, replace the power source PCB. Check if 24 V DC is output from YC8-10 on the main PCB. If not, replace the main PCB.

)Code: C4010 عطل كيوسيرا كود(

وصف الكود:

Polygon motor steady-state problem • When high-speed rotation from lowspeed rotation is requested, the motor does not become stable even after 20 s.

السبب:

Poor contact in the polygon motor connector terminals. Defective polygon motor. Defective power source PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the LSU. Check if 24 V DC is supplied to YC2-1 on the main PCB. If not, replace the power source PCB. Check if 24 V DC is output from YC8-10 on the main PCB. If not, replace the main PCB.

)Code: C4200 عطل كيوسيرا كود(

وصف الكود:

BD steady-state problem • The VTC detects a BD error for 600 ms after the polygon motor rotation has been stabilized.

السبب:

Defective laser diode. Defective polygon motor. Defective main PCB.

حل مشكلة الكود

Replace the LSU. Replace the LSU. Replace the main PCB and check for correct operation.

 

)Code: C5300 عطل كيوسيرا كود(

وصف الكود:

Broken cleaning lamp wire While the cleaning lamp is on, the broken cleaning lamp wire detection signal is detected for 2 s continuously.

السبب:

Defective cleaning lamp. Defective main PCB.

حل مشكلة الكود

Replace the cleaning lamp. Replace the main PCB and check for correct operation.

)Code: C6000 عطل كيوسيرا كود(

وصف الكود:

Broken fixing heater wire • When the power is turned on or at the start of fixing control from the sleep mode, 10 s after fixing heater M is turned on, the detected temperature of fixing thermistor 2 is lower than 40 C/104 F. • When the power is turned on or at the start of fixing control from the sleep mode, 7 s after fixing heater S is turned on, the detected temperature of fixing thermistor 1 is lower than 40C/104 F. • During standby, the detected temperatures of fixing thermistors 1 and 2 become lower than 60 °C/140F

السبب:

Poor contact in the fixing unit thermistor 1 or 2 connector terminals. Fixing unit thermistor 1 or 2 installed incorrectly. Fixing unit thermostat triggered. Fixing unit heater M or S installed incorrectly. Broken fixing unit heater M or S wire.

حل مشكلة الكود

Check the connection of connector YC10 on the main PCB and the continuity across the connector terminals. Repair or replace if necessary. Check and reinstall if necessary. Check for continuity. If none, replace the fixing unit thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the fixing unit heater M or S.

 

)Code: C6020 عطل كيوسيرا كود(

وصف الكود:

Abnormally high fixing unit thermistor temperature • Fixing thermistor 1 detects temperature 250 C/482 F or higher. • Fixing thermistor 2 detects temperature 210 C/410 F or higher.

السبب:

Shorted fixing unit thermistor 1 or 2. Broken fixing unit heater control circuit on the power source PCB.

حل مشكلة الكود

Measure the resistance. If it is 0 Ω, replace the fixing unit thermistor 1 or 2. Replace the power source PCB.

)Code: C6050 عطل كيوسيرا كود(

وصف الكود:

Abnormally low fixing unit thermistor temperature • When only fixing heater M is on, fixing thermistor 2 detects temperature lower than 80 C/176 F during copying. • When fixing heater M and fixing heater S are on, fixing thermistor 2 detects temperature lower than 80 C/ 176 F or fixing thermistor 1 detects temperature lower than 100 C/212 F during copying.

السبب:

Poor contact in the fixing unit thermistor connector terminals. Broken fixing unit thermistor wire. Fixing unit thermistor installed incorrectly. Fixing unit thermostat triggered. Fixing unit heater M or S installed incorrectly. Broken fixing unit heater M or S wire.

حل مشكلة الكود

Check the connection of connector YC10 on the main PCB and the continuity across the connector terminals. Repair or replace if necessary. Measure the resistance. If it is ∞Ω, replace the fixing unit thermistor. Check and reinstall if necessary. Check for continuity. If none, replace the fixing unit thermostat. Check and reinstall if necessary. Check for continuity. If none, replace the fixing unit heater M or S.

)Code: C6400 عطل كيوسيرا كود(

وصف الكود:

Zero-crossing signal problem

• The main PCB does not detect the zero-crossing signal (Z CROSS SIG) for the time specified below. At power-on: 5 s Others: 5 s

السبب:

Poor contact in the connector terminals. Defective power source PCB. Defective main PCB.

حل مشكلة الكود

Check the connection of connectors YC1-3 on the main PCB and YC2-6 on the power source PCB, and the continuity across the connector terminals. Repair or replace if necessary. Check if the zero-crossing signal is output from YC2-6 on the power source PCB. If not, replace the power source PCB. Replace the main PCB if C6400 is detected while YC2-6 on the power source PCB outputs the zero-crossing signal.

(Code: C6410 عطل كيوسيرا كود (

وصف الكود:

Fixing unit connector insertion problem

• Absence of the fixing unit is detected.

السبب:

Fixing unit connector inserted incorrectly. Defective fixing unit connector.

حل مشكلة الكود

Reinsert the fixing unit connector if necessary. Replace the fixing unit.

)Code: C6420 عطل كيوسيرا كود(

وصف الكود:

Fixing unit fuse cut problem

• The fixing temperature remains at 0 °C/32 °F for 30 s continuously when the fixing heater is on.

السبب:

Poor contact in the fixing unit thermistor connector terminals. Broken fixing unit thermistor wire.

حل مشكلة الكود

Check the connection of connector YC10 on the main PCB and the continuity across the connector terminals. Repair or replace if necessary. Measure the resistance. If it is ∞Ω, replace the fixing unit thermistor.

)Code: C7300 عطل كيوسيرا كود(

وصف الكود:

Toner sensor problem

While the toner container sensor is on, the toner sensor in the developing unit does not turn on after the toner sensor turns off and toner is replenished from the toner container. (This code is not displayed. The service call counter counts the frequency of occurrence only as for this code.)

السبب:

Defective toner sensor. Poor contact in the toner sensor connector terminals. Defective toner container sensor. Defective toner container.

حل مشكلة الكود

Replace the toner sensor. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the toner container sensor. Replace the toner container.

)Code: C7400 عطل كيوسيرا كود(

وصف الكود:

Image formation unit connector insertion problem

• Absence of the image formation unit is detected.

السبب:

Image formation unit connector inserted incorrectly. Defective image formation unit connector.

حل مشكلة الكود

Reinsert the image formation unit connector if necessary. Replace the image formation unit.

)Code: C7410 عطل كيوسيرا كود(

وصف الكود:

Drum unit connector insertion problem • Absence of the drum unit is detected.

السبب:

Drum unit connector inserted incorrectly. Defective drum unit connector.

حل مشكلة الكود

Reinsert the drum unit connector if necessary. Replace the drum unit.

(Code: C7450 عطل كيوسيرا كود (

وصف الكود:

Image formation unit fuse cut problem • The input voltage is above 4.5 V.

السبب:

Image formation unit connector inserted incorrectly. Defective image formation unit connector.

حل مشكلة الكود

Reinsert the image formation unit connector if necessary. Replace the image formation unit.

(Code: C7800 عطل كيوسيرا كود (

وصف الكود:

Broken external temperature thermistor wire • The input voltage is above 4.5 V.

السبب:

Poor contact in the humidity sensor PCB connector terminals. Defective external temperature thermistor.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the humidity sensor PCB.

 

(Code: C7810 عطل كيوسيرا كود (

وصف الكود:

Short-circuited external temperature thermistor • The input voltage is below 1.0 V.

السبب:

Poor contact in the humidity sensor PCB connector terminals. Defective external temperature thermistor.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the humidity sensor PCB.

(Code: C8010 عطل كيوسيرا كود (

وصف الكود:

Finisher paper conveying motor problem (3000-sheet finisher) • The paper conveying motor lockup signal is detected for 0.5 s or longer.

السبب:

Poor contact in the paper conveying motor connector terminals. The paper conveying motor malfunctions. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the paper conveying motor and check for correct operation. Replace the finisher main PCB and check for correct operation.

(Code: C8030 عطل كيوسيرا كود (

وصف الكود:

Finisher paper conveying belt problem (3000-sheet finisher) • An on-to-off or off-to-on state change of the paper conveying belt home position sensor is not detected within 2 s of the paper conveying belt clutch turning on.

السبب:

The paper conveying belt is out of phase. The paper conveying belt clutch malfunctions. The paper conveying belt home position sensor malfunctions. The paper conveying belt home position sensor connector makes poor contact. The internal tray is incorrectly inserted.

حل مشكلة الكود

Adjust the paper conveying belt so that it is in phase and check for correct operation. Replace the paper conveying belt clutch and check for correct operation. Replace the paper conveying belt home position sensor and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Check whether the internal tray unit or front cover catches are damaged.

(Code: C8140 عطل كيوسيرا كود (

وصف الكود:

Finisher tray elevation motor problem (3000-sheet finisher) • The sort tray is not detected in the home position within 30 s of the start of the tray elevation motor rotation.

السبب:

Poor contact in the tray elevation motor connector terminals. The tray elevation motor malfunctions. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the tray elevation motor and check for correct operation. Replace the finisher main PCB and check for correct operation.

(Code: C8170 عطل كيوسيرا كود (

وصف الكود:

Finisher front side registration motor problem (3000-sheet finisher or built-in finisher) • If the front side registration home position sensor is on in initialization, the sensor does not turn off within 570 ms of starting initialization. • If the front side registration home position sensor is off in initialization, the sensor does not turn on within 3180 ms of starting initialization.

السبب:

The front side registration motor connector makes poor contact. The front side registration motor malfunctions. The front side registration home position sensor connector makes poor contact. The front side registration home position sensor malfunctions. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the front side registration motor and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the front side registration home position sensor and check for correct operation. Replace the finisher main PCB and check for correct operation.

(Code: C8180 عطل كيوسيرا كود (

وصف الكود:

Finisher rear side registration motor problem (3000-sheet finisher or built-in finisher) • If the rear side registration home position sensor is on in initialization, the sensor does not turn off within 570 ms of starting initialization. • If the rear side registration home position sensor is off in initialization, the sensor does not turn on within 2880 ms of starting initialization.

السبب:

The rear side registration motor connector makes poor contact. The rear side registration motor malfunctions. The rear side registration home position sensor connector makes poor contact. The rear side registration home position sensor malfunctions. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the rear side registration motor and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the rear side registration home position sensor and check for correct operation. Replace the finisher main PCB and check for correct operation.

(Code: C8190 عطل كيوسيرا كود (

وصف الكود:

Finisher trailing edge registration motor problem (built-in finisher) • If the trailing edge registration home position sensor is on in initialization, the sensor does not turn off within 570 ms of starting initialization. • If the trailing edge registration home position sensor is off in initialization, the sensor does not turn on within 4550 ms of starting initialization.

السبب:

The trailing edge registration motor connector makes poor contact. The trailing edge registration motor malfunctions. The trailing edge registration home position sensor connector makes poor contact. The trailing edge registration home position sensor malfunctions. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the trailing edge registration motor and check for correct operation. Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. Replace the trailing edge registration home position sensor and check for correct operation. Replace the finisher main PCB and check for correct operation.

 

(Code: C8210 عطل كيوسيرا كود (

وصف الكود:

Finisher front stapler problem • The front stapler home position sensor does not change state from non-detection to detection within 200 ms of the start of front stapler motor counterclockwise (forward) rotation. • During initialization, the front stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of front stapler motor clockwise (reverse) rotation.

السبب:

The front stapler connector makes poor contact. The front stapler malfunctions. a) The front stapler is blocked with a staple. b) The front stapler is broken. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. a) Remove the front stapler cartridge and check the cartridge and the stapling section of the stapler. b) Replace the front stapler and check for correct operation. Replace the finisher main PCB and check for correct operation.

(Code: C8220 عطل كيوسيرا كود (

وصف الكود:

Linisher rear stapler problem (3000sheet finisher) • The rear stapler home position sensor does not change state from non-detection to detection within 200 ms of the start of rear stapler motor counterclockwise (forward) rotation. • During initialization, the rear stapler home position sensor does not change state from non-detection to detection within 600 ms of the start of rear stapler motor clockwise (reverse) rotation.

السبب:

The rear stapler connector makes poor contact. The rear stapler malfunctions. a) The rear stapler is blocked with a staple. b) The rear stapler is broken. Defective finisher main PCB.

حل مشكلة الكود

Reinsert the connector. Also check for continuity within the connector cable. If none, remedy or replace the cable. a) Remove the front stapler cartridge and check the cartridge and the stapling section of the stapler. b) Replace the front stapler and check for correct operation. Replace the finisher main PCB and check for correct operation.

(Code: C8300 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher paper ejection motor problem

السبب:

A problem is detected with the paper ejection motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8310 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher elevation motor problem

السبب:

A problem is detected with the elevation motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8320 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher rear jog motor problem

السبب:

A problem is detected with the rear jog motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8330 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher front jog motor problem

السبب:

A problem is detected with the front jog motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8340 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher staple motor problem

السبب:

A problem is detected with the staple motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8350 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher batch processing motor problem

السبب:

A problem is detected with the batch processing motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8360 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher stapler shift motor problem

السبب:

A problem is detected with the stapler shift motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8370 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher paddle motor problem

السبب:

A problem is detected with the paddle motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8380 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher folding problem

السبب:

A problem is detected with the folding sensor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8390 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher backup RAM data problem

السبب:

A backup RAM data error is detected.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8410 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher punch motor problem

السبب:

A problem is detected with the punch motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8420 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher shift motor problem

السبب:

A problem is detected with the shift motor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8430 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher punch communication problem

السبب:

A problem is detected with the punch communication.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8440 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher punch sensor problem

السبب:

A problem is detected with the punch sensor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8450 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher side punch sensor problem

السبب:

A problem is detected with the side punch sensor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8460 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher punch backup RAM data problem

السبب:

A problem is detected with the punch backup RAM data.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8470 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher punch dust sensor problem

السبب:

A problem is detected with the punch dust sensor.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8480 عطل كيوسيرا كود (

وصف الكود:

Booklet stitcher broken punch power source wire problem

السبب:

A broken punch power source wire problem is detected.

حل مشكلة الكود

See the booklet stitcher service manual.

(Code: C8500 عطل كيوسيرا كود (

وصف الكود:

Mailbox drive motor problem • While the mailbox drive motor is driving, synchronization signals do not synchronize continually for 464 ms (motor lockup).

السبب:

Defective mailbox drive motor or mailbox main PCB.

حل مشكلة الكود

Run a simulation of the mailbox. If there is any problem with the communication, replace the mailbox drive motor or the mailbox main PCB and check for correct operation.

تعديل المقال