ماكينة تصوير كيوسيرا 180
ماكينة تصوير كيوسيرا 180 - KYOCERA TASKalfa 180
تعتبر ماكينة تصوير كيوسيرا 180 من أفضل الماكينات للطباعة المكتبية للمدارس والسوبر ماركت وهي ماكينة احمال شاقه جدا، كما أنها موفرة جدا في الحبر.
مواصفات الماكينة :
- الموديل : 180ci .
- حالة الماكينة :بدون ديفولبر يعني تعتبر زيرو اعطال.
- دوبلكس التصوير على الوجهين اتوماتيك.
- معدل التحميل الشهري: 500 ألف ورقه.
- دقة ووضوح الطباعة: 600×600 dpi .
- دقة ووضوح التصوير : 600×600 dpi .
- زمن التسخين : 17.2 ثانية.
- مقاس الورق: 3, A4, A5, A6A.
- زمن خروج أول ورقة : 5.7 ثواني.
- عدد النسخ الممكن انتاجها بضغطة واحدة : 1-999 صورة.
- التكبير و التصغير : من 25% إلى 400% ( الزيادة و النقص بي1%).
- سرعة الماكينة : 22 نسخة في الدقيقة الواحدة .
- حجم الذاكرة: 32 MB.
تعريف ماكينة كيوسيرا180 kyocera taskalfa :
لتعريف ماكينة تصوير كيوسيرا 180 اضغط هنا
سعر ماكينة تصوير كيوسيرا 180:
- سعر ماكينة تصوير كيوسيرا 180 استعمال الخارج ( ).
- سعر ماكينة تصوير كيوسيرا 180 جديدة ( ).
كتالوج ماكينة تصوير كيوسيرا 180:
لتحميل كتالوج آلة كيوسيرا 180 اضغط هنا
أعطال ماكينة كيوسيرا : kyocera taskalfa 180:
عطل كودي رقم: code: A0410
Description:Document
processor communication problem Communication fails five times succes-sively.
Causes:Document
processor installed incorrectly.
Defective PWB
Remedy:Document
processor installed incorrectly. Check the installation state of the document
processor and adjust it if it is not properly installed.
Defective PWB. Replace the main/engine PWB or DP driver PWB and check for
correct operation.
عطل كودي رقم: code: A0420
Description:First
paper feeder communication problem
Communication fails five times successively.
Causes:First
paper feeder installed incorrectly.
Defective PWB
Remedy:First
paper feeder installed incorrectly. Check the installation state of the first
paper feeder and adjust it if it is not properly installed.
Defective PWB. Replace the main/engine PWB or cassette main PWB and check for
correct operation.
عطل كودي رقم: code: A0500
Description:Second
paper feeder communication problem
Communication fails five times succes-sively
Causes:Second
paper feeder installed incorrectly.
Defective PWB
Remedy:Second
paper feeder installed incorrectly. Check the installation state of the second
paper feeder and adjust it if it is not properly installed.
Defective PWB. Replace the main/engine PWB or cassette main PWB and check for
correct operation.
عطل كودي رقم: code: A0510
Description:Third
paper feeder communication problem
Communication fails five times succes-sively.
Causes:Third
paper feeder installed incorrectly.
Defective PWB
Remedy:Third
paper feeder installed incorrectly. Check the installation state of the third
paper feeder and adjust it if it is not properly installed.
Defective PWB. Replace the main/engine PWB or cassette main PWB and check for
correct operation.
عطل كودي رقم: code: C0100
Description:Backup
memory (EEPROM) device problem (main)
Reading from or writing to EEPROM cannot be performed.
Causes:Defective
main/ engine PWB.
Remedy:Replace
the main/engine PWB and check for correct operation.
عطل كودي رقم: code: C0110
Description:Backup
memory data problem (main)
Data in the specified area of the backup memory does not match the specified
values.
Causes:Data
damage of EEPROM.
Remedy:Contact
the Service Administrative Division.
عطل كودي رقم: code: C0150
Description:Backup
memory device problem (engine EEPROM)
Reading from or writing to EEPROM cannot be performed
Causes:Defective
main/ engine PWB.
Device damage of EEPROM.
Remedy:Defective
main/ engine PWB. Replace the main/engine PWB and check for correct operation.
Device damage of EEPROM. Contact the Service Administrative Division.
عطل كودي رقم: code: C0160
Description:Backup
memory data problem (engine EEPROM)
Reading data from EEPROM is abnormal.
Causes:Data
damage of EEPROM.
Remedy:Contact
the Service Administrative Division.
عطل كودي رقم: code: C0170
Description:Copy
counts problem
When the power is turned on, the total count and the scan count are abnormal
both on the main and engine.
Causes:Data
damage of EEPROM.
Defective main/ engine PWB.
Remedy:Data
damage of EEPROM. Contact the Service Administrative Division.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C0180
Description:Machine
number mismatch
Machine number of main and engine does not match.
Causes:Data
damage of EEPROM.
Remedy:Contact
the Service Administrative Division.
عطل كودي رقم: code: C0210
Description:Communication
problem between the main and engine
When the power is turned on, the machine does not detect the low level of SBSY
and the high level of SDIR for 10 s.
Causes:Poor
contact in the connector terminals.
Defective main/ engine PWB.
Remedy:Poor
contact in the connector terminals. Reinsert the connector. Also check for
continuity within the connector cable. If none, remedy or replace the cable.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C0240
Description:Printer
PWB communication problem
The printer PWB does not respond 120 s after the power is turned on.
Causes:Poor
contact in the connector terminals.
Defective main/ engine PWB.
Remedy:Poor
contact in the connector terminals. Reinsert the connector. Also check for
continuity within the connector cable. If none, remedy or replace the cable.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C0610
Description:Bitmap
(DIMM) problem
There is a problem with the data or address bus of the bitmap DRAM.
Causes:Defective
main/ engine PWB.
DIMM installed incorrectly.
Defective DIMM.
Remedy:Defective
main/ engine PWB. Replace the main/engine PWB and check for correct operation.
DIMM installed incorrectly. Check if the DIMM is inserted into the socket on
the main/engine PWB correctly.
Defective DIMM. Replace the DIMM and check for correct operation.
عطل كودي رقم: code: C0620
Description:Memory
input interface problem
Reading-in of an image does not complete within 10 s of the start of image
transmission.
Causes:Defective
main/ engine PWB.
Remedy:Defective
main/ engine PWB. Replace the main/engine PWB and check for correct operation.
عطل كودي رقم: code: C0630
Description:DMA
problem
DMA transmission of compressed, decompressed, rotated, relocated or blanked-out
image data does not complete within the specified period of time.
Causes:Defective
main/ engine PWB.
Remedy:Defective
main/ engine PWB. Replace the main/engine PWB and check for correct operation.
عطل كودي رقم: code: C0800
Description:Image
processing problem
JAM05 is detected twice.
Causes:Defective
main/ engine PWB.
Remedy:Defective
main/ engine PWB. Replace the main/engine PWB and check for correct operation.
عطل كودي رقم: code: C2000
Description:Drive
motor problem
A stable state does not continue for 1 s from 1 s after the drive motor is
activated.
Causes:Poor
contact in the connector terminals.
Defective drive transmission system.
Defective main/ engine PWB.
Defective drive motor.
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC6 on
the main/engine PWB and the connector on the drive motor, and the continuity
across the connector terminals. Repair or replace if necessary.
Defective drive transmission system. Check if the rollers and gears rotate
smoothly. If not, grease the bushings and gears. Check for broken gears and
replace if any.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
Defective drive motor. Replace the drive motor.
عطل كودي رقم: code: C2200
Description:Drum
motor problem
A stable state does not continue for 1 s from 1 s after the drum motor is
activated.
Causes:Poor
contact in the connector terminals
Defective drive transmission system.
Defective main/ engine PWB.
Defective drum motor.
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC6 on
the main/engine PWB and the connector on the drum motor, and the continuity
across the connector terminals. Repair or replace if necessary.
Defective drive transmission system. Check if the rollers and gears rotate
smoothly. If not, grease the bushings and gears. Check for broken gears and
replace if any.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
Defective drum motor. Replace the drum motor.
عطل كودي رقم: code: C3100
Description:Scanner
carriage problem
The home position is not correct when the power is turned on or at the start of
copying using the table.
Causes:Poor
contact in the connector terminals.
Defective home position switch
Defective scanner motor
The mirror frame, exposure lamp, or scanner wire is defective
Defective main/ engine PWB.
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC5 on
the main/engine PWB and the connector on the home position switch, and the continuity
across the connector terminals. Repair or replace if necessary.
Defective home position switch. Replace the home position switch.
Defective scanner motor. Replace the scanner motor.
The mirror frame, exposure lamp, or scanner wire is defective. Check if the
mirror flames and exposure lamp are on the rail. And check the scanner wire
winds correctly.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C3200
Description:Exposure
lamp problem
Non-lighting of the exposure lamp is detected at the beginning of copying.
Causes:Poor
contact in the connector terminals.
Defective exposure lamp.
Incorrect shading position.
Defective PWB
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC16 on
the main/engine PWB and the connector on the inverter PWB, and the continuity
across the connector terminals. Repair or replace if necessary.
Defective exposure lamp. Replace the exposure lamp.
Incorrect shading position. Adjust the position of the contact glass (shading
plate). If the problem still occurs, replace the home position switch.
Defective PWB. Replace the main/engine PWB or inverter PWB and check for
correct operation.
عطل كودي رقم: code: C3300
Description:AGC
problem
After AGC, correct input is not obtained at CCD
Causes:Poor
contact in the connector terminals
Defective exposure lamp.
Defective PWB
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC27 on
the main/engine PWB and the connector on the CCD PWB, and the continuity across
the connector terminals. Repair or replace if necessary.
Defective exposure lamp. Replace the exposure lamp.
Defective PWB. Replace the main/engine PWB or CCD PWB and check for correct
operation.
عطل كودي رقم: code: C4000
Description:Polygon
motor synchronization problem
The polygon motor does not reach the stable speed within 20 s of the START
signal turning on.
Causes:Poor
contact in the connector terminals
Defective polygon motor.
Defective main/ engine PWB
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC3 on
the main/engine PWB and laser scanner unit, and the continuity across the
connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C4010
Description:Polygon
motor steady-state problem
Stable OFF is detected for 5 s continuously after polygon motor stability.
Causes:Poor
contact in the connector terminals.
Defective polygon motor.
Defective main/ engine PWB.
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC3 on
the main/engine PWB and laser scanner unit, and the continuity across the
connector terminals. Repair or replace if necessary.
Defective polygon motor. Replace the laser scanner unit.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C4200
Description:BD
steady-state problem
ASIC detects a BD error for 600 ms after the polygon motor rotation has been
stabilized.
Causes:Poor
contact in the connector terminals
Defective laser scanner unit.
Defective main/ engine PWB
Remedy:Poor
contact in the connector terminals. Check the connection of connector YC3 on
the main/engine PWB and laser scanner unit, and the continuity across the
connector terminals. Repair or replace if necessary.
Defective laser scanner unit. Replace the laser scanner unit.
Defective main/ engine PWB. Replace the main/engine PWB and check for correct
operation.
عطل كودي رقم: code: C6000
Description:Fuser
heater break
The temperature does not reach 70 °C/ 158°F in 15 s before secondary
stabilization.
Temperature rise of 1°C/1.8°F does not occur in 5 s before secondary
stabilization (except during printing).
Causes:Poor
contact in the fuser thermistor connector terminals.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy:Poor
contact in the fuser thermistor connector terminals. Reinsert the connector.
Also check for continuity within the connector cable. If none, remedy or
replace the cable.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser
thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser
heater.
عطل كودي رقم: code: C6020
Description:Abnormally
high fuser thermistor temperature
Fuser thermistor is detected 230°C/ 446°F or more for 40 ms.
Causes:Shorted
thermistor.
Broken heater control circuit on the power source PWB
Remedy:Shorted
thermistor. Measure the resistance. If it is 0Ω, replace the thermistor.
Broken heater control circuit on the power source PWB. Replace the power source
PWB and check for correct operation.
عطل كودي رقم: code: C6050
Description:Abnormally
low fuser thermistor temperature
Fuser thermistor remains below 90°C/ 194°F for 1 s.
Causes:Poor
contact in the fuser thermistor connector terminals.
Broken fuser thermistor wire.
Fuser thermistor installed incorrectly.
Fuser thermostat triggered.
Fuser heater installed incorrectly.
Broken fuser heater wire.
Remedy:Poor
contact in the fuser thermistor connector terminals. Reinsert the connector.
Also check for continuity within the connector cable. If none, remedy or
replace the cable.
Broken fuser thermistor wire. Measure the resistance. If it is ∞, replace the
fixing thermistor.
Fuser thermistor installed incorrectly. Check and reinstall if necessary.
Fuser thermostat triggered. Check for continuity. If none, replace the fuser
thermostat.
Fuser heater installed incorrectly. Check and reinstall if necessary.
Broken fuser heater wire. Check for continuity. If none, replace the fuser
heater.
عطل كودي رقم: code: C6400
Description:Zero-cross
signal error
Interrupt of the zero-cross signal does not occur more than 1 s.
Causes:Poor
contact in the connector terminals
Defective power source PWB.
Defective main/ engine PWB.
Remedy:Poor
contact in the connector terminals. Reinsert the connector. Also check for
continuity within the connector cable. If none, remedy or replace the cable.
Defective power source PWB. Check if the zero-crossing signal is output from
YC2-2 on the power source PWB. If not, replace the power source PWB.
Defective main/ engine PWB. Replace the main/engine PWB if C6400 is detected
while YC2-2 on the power source PWB outputs the zero-crossing signal.
عطل كودي رقم: code: C7800
Description:Broken
external thermistor wire
The thermistor output value is 0.5 V or less.
Causes:Poor
contact in the connector terminals.
Defective humidity sensor.
Remedy:Poor
contact in the connector terminals. Reinsert the connector. Also check for
continuity within the connector cable. If none, remedy or replace the cable.
Defective humidity sensor. Replace the cassette PWB and check for correct
operation.
عطل كودي رقم: code: C7810
Description:Short-circuited
external thermistor wire
The thermistor output value is 4.5 V or more.
Causes:Poor
contact in the connector terminals.
Defective humidity sensor.
Remedy:Poor
contact in the connector terminals. Reinsert the connector. Also check for
continuity within the connector cable. If none, remedy or replace the cable.
Defective humidity sensor. Replace the cassette PWB and check for correct
operation.